Air Dryer Removes Need For External Filtration

Nano-Porous Solutions' ultra-high purity desiccant air dryer eliminates the need for external filtration and problems associated with the mechanical failure of condensate float drains. This can ultimately cause failure of the dryer. The dryer offers a filter/desiccant cartridge that incorporates water separation. This feature eliminates the need for external filtration and problems associated with the mechanical failure of condensate float drains, which can ultimately cause failure of the dryer.

With Nano-Porous Systems' air dryer, condensate is collected within an internal quiet zone/chamber, which is expelled every two minutes through timed solenoid waves. The dryer design is highly energy efficient - integrated filtration and extremely good flow distribution across the desiccant beds have reduced pressure drop through the dryer by an impressive 60 per cent. It achieves lower running costs than other desiccant air dryers and meets the highest standards of purity.

The dryer is ready to run at any location worldwide. A neat switch-mode power supply means it will operate to suit American, European and Japanese power supplies. Maintenance and installation are simple. The dryer's water separation, inlet and outlet filtration significantly increase reliability.

The elegant silver and black dryer has an easy-to-read text display screen to check each stage of operation and drying cycles. It is available in five sizes with flows between 3 and 24scfm and can be floor- or wall-mounted. The ultra-high purity desiccant air dryer ensures that when it is used close to the point of application, any compressed air that comes into contact with people, animals, food, drinks, medical equipment or pharmaceutical products is dry, clean, safe and contaminant free.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more