Hepcomotion Offers SBD 30-100XL Sealed Belt Drive

Hepcomotion has added the SBD 30-100XL to its sealed belt drive (SBD) linear motion product programme, offering high loads and long spans for bespoke machines and handling systems. The SBD 30-100XL is 2.5 times stiffer than its standard counterpart and has greater load-bearing capabilities. The Hepcomotion SBD is described as a high-performing yet cost-competitive product that provides a compact and clean solution.

Because it is sealed, it keeps on working in applications where other systems can fail. A stainless steel cover strip runs the entire length of the high-strength aluminium beam, houses the linear guide and belt and provides good protection against dirt and debris.

It is this anodised aluminium beam that is the differentiator on the SBD 30-100XL, according to Hepcomotion. The greater stiffness of the 100m-wide beam on the product makes it suitable for any application where underside support is limited or even non-existent. It can also be used to span two parallel X axes - subject to load - with no further support.

This will enable one unit to be used as opposed to two smaller units fitted together. The SBD 30-100XL is suitable for high-speed operation, generally up to 4m/sec, and driven by a polyurethane, steel-reinforced, 50mm-wide toothed belt. Its tension is factory set but adjustments can easily be made via tensioning screws.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more