Rolec Offers Industry-Standard Die-Cast Enclosures

Rolec has introduced a range of die-cast enclosures for applications including process control equipment, monitoring and detection systems, flow metering, terminal housings and machine controllers. The industry-standard Aluplus series of enclosures incorporates many of the features of the Alucase designer range. Unlike older die-cast enclosures, the Aluplus series features a sharp external design that includes snap-on design trims. These fit into the lid section and hide both the assembly and mounting screws; as a result, they provide a clean appearance with no visible fixing screws.

With Aluplus, it is no longer necessary to machine the lid to fit membrane keypads or polycarbonate labels; a 1.7mm recessed area is already provided. In addition, external mounting brackets are no longer required as the enclosures can be mounted to a wall or machine while still assembled. There is no need to remove the lid, thus avoiding any possible damage to the components or sealing gasket. The clip-on trims are simply snapped into place after the unit is mounted. The Aluplus enclosures are rated to IP 66 as standard, but can also be specified to IP 67 and IP 69K with special factory-fitted gaskets.

The enclosures are manufactured in die-cast aluminium and powder painted in a fine textured light grey (RAL 7035). The range is currently available in the four most popular industry-standard sizes: 122 x 120 x 82mm, 220 x 120 x 82mm, 160 x 160 x 90mm and 260 x 160 x 90mm. Other industry-standard sizes are planned. Screw bosses are provided in the base and lid sections for printed circuit boards (PCBs), mounting plates, earth leads and other components (screws included).

Prices for the Aluplus start at GBP49. Accessories include special lid fixing screws with integrated retaining straps. These keep the lid in situ during installation and servicing. Rolec offers a full customising service on these enclosures with CNC milling, drilling, silk-screen printing and the assembly of cable glands and terminals, providing a fully finished housing ready for fitting the components.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more