SEW Eurodrive MOVIMOT Gearmotor with Integrated Frequency Inverter Options



MOVIMOT can be equipped with a BEM, BES or URM brake control system as an option in conjunction with a modular terminal box. The option is integrated in the MOVIMOT terminal box. BEM controls the standard brake, BES controls the DC 24 V brake. URM is a voltage relay for controlling brakes.

The BW100***/BW200*** braking resistors in IP65 enclosure convert the MOVIMOT drive's regenerative energy of up to 100 W/200 W (0.134 hp / 0.268 hp) continuous power into heat.

The BW150**/BW068** braking resistors in IP66 enclosure convert the MOVIMOT drive's regenerative energy of up to 600 W/1200 W (0.805 hp /1.609 hp) continuous power into heat.

The optional DC 24 V power supply MLU11A is mounted in one of the MOVIMOT cable entry openings and allows for operation of one MOVIMOT® including an option with a current consumption of up to 70 mA (MBG11A, MWA21A) without an external 24 V auxiliary power supply.

The optional integrated DC 24 V power supply MLU13A is mounted in the MOVIMOT terminal box and allows for operation of one MOVIMOT® including an option with a current consumption of up to 70 mA (MBG11A, MWA21A) without an external 24V auxiliary power supply.

The optional MLG**A setpoint generator is mounted in one of the cable entry openings of MOVIMOT and offers the possibility of adjusting the input speed in the range of -100% to +100 % fmax (potentiometer f1) as well as of powering the inverter with the DC 24 V auxiliary voltage.

The optional MBG11A setpoint control module has two keys and a display. MBG11A** makes it possible to adjust the speed remotely in the range from -100% to +100% fmax (potentiometer f1). Up to 31 MOVIMOT units can be controlled at the same time.

The optional MWA21A setpoint converter converts an analog setpoint and the control signals into an RS-485 protocol. The MWA21A enables the MOVIMOT to be controlled remotely from the control cabinet. Up to 31 MOVIMOT units can be controlled at the same time.

The DBG60B keypad can be used to control MOVIMOT drives with integrated AS interface in manual mode. Furthermore, important information can be displayed in monitor mode.

The DBG60B keypad is connected to the diagnostic interface in the MOVIMOT terminal box.

The optional MDG11A diagnostic unit indicates the operating status, output current, terminal status and MOVIMOT® fault codes when faults occur.

The MNF11A integrated line filter option is mounted in the MOVIMOT terminal box and allows for a drive system that complies with the emitted interference stipulated in EN 61800-3 as well as with the class B limit according to EN 55011 and EN 55014.

The P2.A mounting plate option allows the MOVIMOT inverter to be mounted away from the motor (offset). The inverter is connected to the motor using a pre-fabricated hybrid cable. MOVIMOT with option P2.A is supplied in enclosure IP65.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more